Valid 300-180 Dumps shared by ExamsLabs.com for Helping Passing 300-180 Exam! ExamsLabs.com now offer the newest 300-180 exam dumps, the ExamsLabs.com 300-180 exam questions have been updated and answers have been corrected get the newest ExamsLabs.com 300-180 dumps with Test Engine here:
https://www.examslabs.com/Cisco/CCNP-Data-Center/best-300-180-exam-dumps.html
(372 Q&As Dumps, 30%OFF Special Discount: 30free)

NEW QUESTION: 1

What is the FCF-MAC tor this switch?

A. 54:7f:ee:98:9b:43

B. 54:7f:ee:98:9b:39

C. 54:7f:ee:98:9b:40

D. 54:7f:ee:98:9b:41

E. 54:7f:ee:98:9b:42

Answer: A

NEW QUESTION: 2

Refer to the exhibit.

Which mistake did the UCS administrator make when trying to access the GUI?

A. password is incorrect

B. did not use the VIP

C. tried to login before the GUI had fully booted up

D. specified the incorrect login domain

E. attempted to login to the subordinate cluster peer

Answer: E

NEW QUESTION: 3

Which two commands check for DIMM errors in a Cisco UCS environment? (Choose two.)

A. UCS-TEST/chassis#show error-recovery

B. UCS-TEST/chassis/server/memory-array #show block

C. UCS-TEST/chassis/server#show memory-array detail

D. UCS-TEST/chassis/server#show error-recovery

E. UCS-TEST/chassis/server#show execute-disable

F. UCS-TEST/chassis/server/memory-array#show stats

Answer: C,F

NEW QUESTION: 4

Which command on the Fabric Interconnect displays packet statistics for a given QoS group

and MTU size?

A. show queuing interface ethernet x/y

B. show interface queuing ethernet x/y

C. show interface ethernet x/y

D. show class-map type qos

E. show policy-map interface ethernet x/y

Answer: A

NEW QUESTION: 5

You are troubleshooting an FCoE boot issue on a Cisco UCS C220 M3 server with a VIC

1225 CNA. Which two pieces of information can you directly infer from the output of the show zone

active command below? (Choose two.) zone name Server_1-to-Storage vsan 11 pwwn

50:06:01:60:3b:a0:08:9f [Storage]

* fcid 0x3b000b [pwwn 20:00:00:25:b5:04:0a:02] [C22_Server]

A. The storage controller is not logged into the fabric.

B. The initiator and target cannot communicate because they are on the wrong VSAN.

C. The initiator and target cannot communicate because the zone name does not match the server

name (C22_Server).

D. The WWPN of the storage controller is mistyped.

E. Only the server is logged into the fabric.

F. The server is not logged into the fabric.

G. Only the storage controller is logged into the fabric.

Answer: A,E

NEW QUESTION: 6

Which names are reserved when custom roles are created in Cisco UCS Manager RBAC?

A. ucs-admin, ucs-operator, server-admin, server-operator, and cisco-admin

B. ucs, ucs123, server-admin, server-operator, and sysroot

C. cisco, cisco123, cisco-operator, cisco-admin, and root

D. network-admin, network-operator, vdc-admin, vdc-operator, and server-admin

Answer: D

NEW QUESTION: 7

A customer is troubleshooting QoS in a Cisco UCS domain due to high packet drops in the

network. The customer has configured the vNIC and associated QoS policy, and changed the MTU

from 1000 to 1200. Packet drops still exist. What is the cause of this issue?

A. The MTU specified here must be equal to or less than the MTU specified in the associated QoS

system class. If this MTU value exceeds the MTU value in the QoS system class, packets may be

dropped during data transmission.

B. The MTU specified here must be less than the MTU specified in the associated QoS system policy.

If this MTU value exceeds the MTU value in the QoS system policy, packets may be not be dropped

during data transmission.

C. The MTU must be optimized and should be changed to fc with the CLI command set mtu fc.

D. The MTU specified here must be greater than the MTU specified in the associated QoS system

class. If this MTU value is less than the MTU value in the QoS system class, packets may be dropped

during data transmission.

Answer: A

NEW QUESTION: 8

You successfully install VMware ESXi 5.0 U1 on a Cisco UCS B200 M3 server to a Fibre Channel

LUN. When you reboot the server, you see the message "Reboot and Select Proper Boot device or

insert Boot Media in selected Boot device and press a key." What are the first two pieces of

information you should gather to troubleshoot the boot failure?

(Choose two.)

A. Validate that the boot order indicates the vHBA as the first device.

B. Validate the boot target WWPN and LUN ID in the service profile.

C. Connect to the NX-OS shell via the CLI and run the show npv flogi-table command.

D. SSH to the MDS 9124 and run the show flogi database command.

E. Validate the correct source WWPN in the service profile vHBA definition.

F. Ensure LUN masking is correctly configured on the storage controller.

G. Validate zoning for your WWPN on the Cisco MDS 9124.

Answer: A,B

NEW QUESTION: 9

You have a Cisco UCS Fabric Interconnect in Fibre Channel end-host mode. You must check

whether all of the Fibre Channel targets are available through the fabric interconnect at VSAN 200.

Which command must you use?

A. show zoneset active VSAN 200

B. show npvflogi-table

C. show flogi database

D. show flogi-table

Answer: B

NEW QUESTION: 10

What can prevent you from adding an interface to a pre-existing port-channel on a CISCO

Nexus N7K device?

A. The interface already assigned to a different port-channel,

B. The interface has been allocated to a different VOC

C. no shutdown was issued on the interface.

D. The port-channel is In LACP passive mode

Answer: A

NEW QUESTION: 11

Refer to the exhibit.

A customer is having problems with NPV. Which of these is the cause of the problem?

A. VSANs are misconfigured on the upstream ports.

B. One external link must be up for server interface to be up.

C. VLANs are misconfigured on the upstream ports.

D. Internal links are down and must be up for the server interface to be up.

E. No server was requested or received by the FLOGI database.

Answer: A

NEW QUESTION: 12

A customer would like to create an Ethernet traffic monitoring session on a Cisco UCS server

to troubleshoot network connectivity. The customer has entered the following commands via CLI:

UCS-A# scope eth-traffic-mon

UCS-A /eth-traffic-mon # scope fabric a

UCS-A /eth-traffic-mon/fabric # create eth-mon-session EthMonitor33

UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create dest-interface 2 12 UCS-A /eth-traffic-

mon/fabric/eth-mon-session/dest-interface* # set speed 20gbps UCS-A /eth-traffic-mon/fabric/eth-

mon-session/dest-interface* # commit-buffer UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-

interface # Which outcome will this command sequence produce?

A. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination

port at slot 2, port 33, will set the admin speed to 20 Gb/s, and will commit the transaction.

B. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination

port at slot 33, port 12, will set the admin speed to 20 Gb/s, and will commit the transaction.

C. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination

port at slot 2, port 12, will set the admin speed to 20 Gb/s, and will commit the transaction.

D. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination

port at slot 2, port 12, will set the admin speed to 10 Gb/s, and will commit the transaction.

Answer: C

https://www.lead2passexam.com/Cisco/valid-300-180-exam-dumps.html

NEW QUESTION: 13

How can you identify the blade location when tracing server traffic?

A. by collecting traffic that uses a SPAN monitoring port

B. by using a trace utility

C. by examining the interface to which the server MAC address is connected

D. by performing CDP checks on the Cisco UCS Fabric Interconnects

Answer: C

NEW QUESTION: 14

At any given time, each server can be associated with how many service profiles?

A. unlimited

B. 1

C. 10

D. 5

E. 2

Answer: B

NEW QUESTION: 15

Refer to the exhibit.

When your customers have NPV problems, which three actions should you take? (Choose three.)

A. Verify that all ports are properly configured and connected.

B. Verify the status of the servers and external interfaces, using the show npv server status

command.

C. For all the device links, ensure that the port mode on the NPV device is in Full_port mode.

D. Ensure that the VLAN values are configured on both sides of the NPV core switch.

E. Verify that the NPV core switch supports NPIV and that it is enabled.

F. Ensure that the VSAN value that is configured on the device links is correct.

Answer: A,E,F

NEW QUESTION: 16

A customer is configuring a network control policy in a Cisco UCS domain. The network

control policy configures the network control settings for the Cisco UCS domain, including which

three of these? (Choose three.)

A. the action that the Cisco UCS Manager takes on the remote Ethernet interface, vEthernet

interface, or vFibreChannel interface when the associated border port fails

B. whether MAC registration occurs on a per-vNIC basis or for all VLANs

C. how the VIF behaves if no uplink port is available in end-host mode

D. Layer 2 switching on the fabric interconnect

E. the end-host mode setting on the I/O module

Answer: A,B,C

NEW QUESTION: 17

Which option describes why the merge status for any application shows "In Progress" for a

prolonged period of time when a new switch is added to the fabric?

A. The merge status cannot occur until a copy running-config startup-config is done.

B. The ports between the switches are not trunking all VSANs.

C. The new switch must be upgraded to match the same version of code as the original switch.

D. The application needs to be started on both switches.

E. There are outstanding changes that must be committed.

Answer: E

NEW QUESTION: 18

What are the minimum number and maximum number of members that a SAN

PortChannel can have?

A. 1, 16

B. 2 minimum with no maximum

C. 1, 32

D. 2, 32

E. 1 minimum with no maximum

F. 2, 16

Answer: A

NEW QUESTION: 19

Refer to the exhibit.

VSAN traffic is not being routed through SAN fabric. Which action is helpful to resolve the problem?

A. Make sure that the FSPF hello timers are different so that they do not compete.

B. Make sure that the FSPF hello interval value matches on both switches.

C. Change the FSPF hello timer back to the default of 5 seconds.

D. Make sure that the FSPF dead timers are both set to 0.

Answer: B

NEW QUESTION: 20

Which configuration is needed to suppress duplicate IP addresses when HSRP localization is

enabled?

A. Configure matching passwords in each data center.

B. Change one data center to run VRRP rather than HSRP.

C. Configure no ip arp gratuitous hsrp duplicate under the VLAN.

D. Remove the passwords in each data center.

E. Configure mismatching HSRP versions between data centers.

Answer: C

https://www.examslabs.com/Cisco/CCNP-Data-Center/best-300-180-exam-dumps.html